Stellar Industries, Inc.

Dealer Login | Site Map | Contact

The Stellar Cable Hoist (Cable75)

Through the use of innovative design processes, Stellar has improved numerous items on the cable hoist. With the use of advanced design software, Stellar has decreased the shipping weight of the Cable75* to 4,400-pounds, which in turn increases the payload by up to 1,700 additional pounds.

Another feature of the Cable75 is the cable routing now spins in a single direction of rotation only, eliminating switching directions when winching in and out, which can cause unnecessary wear on the cable. The design of the Cable75 now includes only a single reeving cylinder that is always covered by a structural enclosure, decreasing its exposure to damaging debris. Having only one cylinder decreases the amount of maintenance required with less seal kits to maintain. The sheave bushings and pins are stainless steel, and bushings and grease zerks are installed in both rod-end pin bosses to improve operation and maintenance. High strength wear strips have been added to the mainframe, and ½” high strength wear plates were added to the end of the mainframe tubes to increase strength and durability.

Stellar has incorporated the use of a hydraulic piston pump on the Cable75. Piston pumps are more efficient, have a longer life, and handle higher operating pressure and pressure spikes better than gear pumps. Using a piston pump has also decreased the gpm (gallon per minute) requirements due to operating at a higher pressure, therefore decreasing the size of the hydraulic oil reservoir from 60-gallons down to 25-gallons. This also contributes to a greater payload capacity.

Features and Benefits
Shipping weight	Cable75 weighs 4,400 lbs. This is 1,700 lbs less than current SI60 cable hoist. This means 1,700 lbs more payload capacity and less hauling costs per year.
Lift and dump capacity	Up to 75,000 lbs lifting and dumping capacity. The capacity is determined by the hydraulic pressure setting. 75,000 lbs capacity pressure setting is 4,500 psi and for 60,000 lbs capacity is approximately 3,600 psi.
Cable	7/8” cable diameter (6x37 EXIWRC) is standard. No need to upgrade to 1” cable if setting hoist for 75,000 lb lift capacity.
Cable routing	Cable is routed in a single direction of rotation. Cable routing does not switch directions from clockwise, to counter clockwise, then back to clockwise. The Cable75 cable runs only in one direction.
Single reeving cylinder	One 6.5” x 80” cylinder instead of two 7” x 80” cylinders that are used on current cable hoists today, therefore there are less seal kits to maintain. Sheave bushings and pins are greaseless. Bushings and grease zerks are installed in both rod-end pin bosses.
Reeving cylinder enclosure	Reeving cylinder rod is always covered by structural enclosure, which decreases the potential to expose the cylinder to damaging debris.
Dump cylinders	Two 5”x71” dump cylinders. Higher operating pressure allows for smaller cylinders, meaning greater payload each pull made. Bushings and grease zerks are installed in both pin bosses.
Hydraulic piston pump	Piston pumps are more efficient, have longer life, handle higher operating pressure and pressure spikes better than gear pumps.
25-gallon oil reservoir	Because of the designed gpm requirements, a larger reservoir is not required. Also contributes to a greater payload capacity.
Functional speed	Hoist up = 30 seconds, hoist down = 11 seconds, cable in loaded = 30 seconds, cable out (unloading) = 30 seconds
Stainless steel pins	Stainless steel pins are used in rear hinge, sheaves, and cylinders.
Bushings and grease zerks	Bushings and grease zerks at installed at all pivot points.
Finish paint	Two part polyurethane automotive finish paint.
Dump cylinder mounting	This new design doubles the shear strength and makes for easier pin removal.
Wear strips	High strength wear strips added to main frame.
Main frame end plates	1/2” high strength wear plates added to end of main frame tubes.
Warranty	36 months structural, 12 months parts and labor.